Showing posts with label welding. Show all posts
Showing posts with label welding. Show all posts

Monday, April 3, 2023

I hope I don't lose my membership

 In the Procrastinators Guild.


Over the last couple weeks I sealed up the hydraulic tank on my garden tractor loader project. I got the machine back in 2017, you guys might have forgotten about it. Checking back it looks like I haven't written about the loader since 2017 which is weird, we've come a long way...

Heres a shot from back when I got it:


Last week I reinstalled the tank, it had leaked where I added the hose fittings so I slathered the inside with POR15 gas tank sealer. It didn't leak overnight so yesterday I fired it up. It did NOT want to run but finally got going, smoked a lot but I'll be darned if it didn't work pretty good.




I moved some snow out of the shadows on our yard over to the storm drain which gets more sun.
Everything was going great until:



That's the upper bucket cylinder mount, or rather there should be a mount there. Apparently I'd only tacked it on and the tacks broke. I wanted to move the mount a little higher anyway.

While I was working I finished cutting the bucket down: 



I took 3" off each side of the bucket, bringing it down to 38" which is still about 2" wider than the machine. Took probably 25# off the weight of the bucket making it much more manageable for the machine. There's still some more to come off but it's much improved.

I'm going to take it over to buddy Ben's house for final welding, he's got a big stick welder so I can really burn in the mounts, my MIG works okay but doesn't really have enough heat for the job...

Thursday, August 6, 2009

Ranger repairs

My dad always said that when you buy a used car you buy somebody else's problems. My Ranger is a 2003 but when we bought it only had 25,000 miles. That means at some point it sat... Well when things sit the rust monster gets to make a play for them. On the Ranger the rust monster got to the bed and in places got to it BAD. It had 3 or 4 good size rust holes and when I attacked with a screwdriver they got worse. So Monday I pulled the bed off (lousy job when working alone) and started cutting. I ended up with about 1.5 square feet of bed cut out. I'd bought a repair panel from JC Whitney and some angle iron from the hardware store. The angle iron is to remake some of the bracing underneith that had rusted. Its MUCH stronger than the origninal. The repair panel doesn't match the bed exactly but isn't too bad.
Tuesday I had to take off because I'd hurt my back pulling the bed (bad job as I said). Yesterday and today were spend grinding and welding, welding and grinding but finally all the repairs are done. The underside of the bed has been painted and then covered in rubberized undercoating. Tomorrow I'll get Randy and Chuck to come over and remount the bed (no big job with 3 guys) and then I'll paint the patch panels and coat the whole bed with Herculiner.

I used Herculiner on the Dakota 10 years ago this year and that bed had no rust inside when I traded the truck. Its good stuff and helps keep stuff from sliding in the bed. I hadn't coated the Dakota thick enough because cold weather caught me, this time I'm going to do both coats in 2 days so I should be okay.

I think the patch looks like hell but Angie says it looks good to her and anyway its way better than rust so that makes me feel good. Still I think I'll either put a piece of plywood or a rubber bedmat over it...

Wednesday, July 2, 2008

Done and done

Heres the before. This is with all the rotted metal removed.
And after.
Thats a coat of paint and a good thick coat of undercoat.

Tomorrow theres a rust spot behind the rear wheel to take care of. I don't know if that'll require welding but it'll get POR15. Then I want to get the new antenna installed so I can see if the one in this car can combine with the one from Hammie to make a working one. Otherwise Hammie gets an eBay antenna too.

-Curt

Don't touch, HOT!

Yeah, after you weld a piece in and then grind off the excess weld, don't touch it without gloves on. I don't care if the gloves are in your way and you can't feel if your welding was good enough...

The burn is 22ga, the same thickness as the metal I was welding in and goes right across where the blister I got from Hammie a couple weeks ago had healed up...

Buttttt the second jack point is all welded, ground down and painted. Pretty soon I'll go hit it with the undercoating.

-Curt

Welcome to July!

Summer is here and what better time to weld up the ravages of winter? Yeah its 95 degrees out, lets haul out the welder! Genius...
Anyway the area around the jack points on my 190D is in pretty terrible shape so I started with the passenger side. What I'd thought were streamers of metal hanging out were in fact the rubber undercoating, there was basically no metal there. I cut back to good metal and welded in a bunch of 22ga sheet metal. 22ga seems about like what I was cutting away, maybe slightly heavy but this is an area that'll have a hard life...
I had to weld 2 plates into the side, one big one to cover the old jack point (I hate those jack point jacks, I use a scissors jack and lift from underneith anyway) and a small one up under the door. Then another big plate underneith the car. I slapped some black Rustoleum on and when it had dried sprayed some rubber undercoating on for good measure.
Not too bad I don't think.

This is the driver's side. I spent a few minutes last night picking the rust and undercoating off. Its pretty much the same as the passenger's side, actually this side isn't as bad...

Well, back at it...

-Curt